FROG @ease Floating System

The Alternative Way to Sanitize

Quick & easy Hot Tub Sanitizer with minerals that uses up to 75% Less Chlorine

How many times have you thought, “this hot tub is just too much work!” We set out to change that with FROG @ease – it gives you that “ahhhh” feeling of relaxation and peace of mind. FROG @ease combines sanitizing minerals with SmartChlor Technology to kill bacteria 2 ways. The result is Fresh Mineral Water that’s silky soft with far fewer odors and the easiest water to maintain because it’s self-regulating. It knows when more sanitizing power is needed and automatically delivers it, and when you need to do something, it flips over.

Up to 75% less chlorine with no frustrating yo-yo chlorine levels

Self regulates for continuous crystal clear water

Shock only once or twice a month with no mixing chemicals

No constant monitoring

Exclusive Frog @ease Test Strips – single color match for easy reading

Easy on hot tub surfaces with less odors

START-UP INSTRUCTIONS

1

Fill the hot tub with fresh water by placing your hose in the gray filter standpipe to approximately half an inch below the pillows. If you have well water: after 10 minutes, install the EcoOne Hose Filter. Flush filter 3-5 seconds outside spa to remove carbon, and complete the filling process.

2

Once the spa is full, power on. *If your source water is high in calcium, iron, or other metals, please contact us for further instructions.

3

IMPORTANT: Always follow printed instructions on the balancing chemical packages. Add balancing chemicals in small increments one at a time with the jets on and wait 6 hours before testing again and adding any
additional balancing chemicals.

4

Test the water with FROG @ease Test Strips and balance according to the Water Balance Guidelines. Make sure to balance Total Alkalinity FIRST, then pH, and finally Calcium Hardness.

Water Balance Guidelines

  • Total Alkalinity: 80-120 ppm
  • pH: 7.2 - 7.8
  • Calcium Hardness: 150 - 250 ppm
5

Establish an initial chlorine residual of 0.5-1.0 ppm with the FROG Jump Start start-up shock, included in the Start-Up kit - one packet per 600 gallons. After the product has bubbled for a few seconds, turn on the high speed jets until fully dissolved.

6

Set the dial on the bottom of the silver FROG SmartChlor Cartridge to the appropriate level in order to maintain a 0.5-1.0 ppm chlorine level.

#1 - 200-300 gal | #2 - 301-450 gal | #3 - 451-550 gal | #4 - 551-600 gal

Connect the blue Mineral Cartridge to the silver SmartChlor Cartridge and twist the cartridges to lock.

7

Place the connected cartridges in your hot tub and enjoy weeks of Fresh Mineral Water hot tub care!

When the FROG @ease System flips over, replace the SmartChlor Cartridge and recycle the empty one.

The SmartChlor Cartridges typically last 3-4 weeks, depending on the size of your spa and usage.

8

Your hot tub is safe to use once the Total Alkalinity, pH, and Calcium Hardness levels measure in the "OK" range on your FROG Test Strip.

After the first 24 hours, saturate the filter surface with SpaGuard Filter Cleaner, allow the filters to sit for 15-20 minutes, then hose off with a high pressure hose or Water Wand. Ensure ALL soap is removed before placing the filters back to avoid foaming.

It is recommended that you test your water every day or so over the first week to ensure the spa water remains balanced and sanitized while the system acclimates to your usage. It's common to need to add Chlorinating Concentrate or Enhanced Shock during this period.

Keep in mind that there are trace amounts of remaining water left in the plumbing from factory testing. Your hot tub will probably also receive higher than normal usage during the first month of ownership. For those reasons, your FROG System will be working overtime to sanitize the water and maintain a chlorine residual during the first week or so.

1

Fill the hot tub with fresh water by placing your hose in the gray filter standpipe to approximately half an inch below the pillows. If you have well water: after 10 minutes, install the EcoOne Hose Filter. Flush filter 3-5 seconds outside spa to remove carbon, and complete the filling process.

2

Once the spa is full, power on. *If your source water is high in calcium, iron, or other metals, please contact us for further instructions.

3

IMPORTANT: Always follow printed instructions on the balancing chemical packages. Add balancing chemicals in small increments one at a time with the jets on and wait 6 hours before testing again and adding any
additional balancing chemicals.

4

Test the water with FROG @ease Test Strips and balance according to the Water Balance Guidelines. Make sure to balance Total Alkalinity FIRST, then pH, and finally Calcium Hardness.

Water Balance Guidelines

  • Total Alkalinity: 80-120 ppm
  • pH: 7.2 - 7.8
  • Calcium Hardness: 150 - 250 ppm
5

Establish an initial chlorine residual of 0.5-1.0 ppm with the FROG Jump Start start-up shock, included in the Start-Up kit - one packet per 600 gallons. After the product has bubbled for a few seconds, turn on the high speed jets until fully dissolved.

6

Set the dial on the bottom of the silver FROG SmartChlor Cartridge to the appropriate level in order to maintain a 0.5-1.0 ppm chlorine level.

#1 - 200-300 gal | #2 - 301-450 gal | #3 - 451-550 gal | #4 - 551-600 gal

Connect the blue Mineral Cartridge to the silver SmartChlor Cartridge and twist the cartridges to lock.

7

Place the connected cartridges in your hot tub and enjoy weeks of Fresh Mineral Water hot tub care!

When the FROG @ease System flips over, replace the SmartChlor Cartridge and recycle the empty one.

The SmartChlor Cartridges typically last 3-4 weeks, depending on the size of your spa and usage.

8

Your hot tub is safe to use once the Total Alkalinity, pH, and Calcium Hardness levels measure in the "OK" range on your FROG Test Strip.

After the first 24 hours, saturate the filter surface with SpaGuard Filter Cleaner, allow the filters to sit for 15-20 minutes, then hose off with a high pressure hose or Water Wand. Ensure ALL soap is removed before placing the filters back to avoid foaming.

It is recommended that you test your water every day or so over the first week to ensure the spa water remains balanced and sanitized while the system acclimates to your usage. It's common to need to add Chlorinating Concentrate or Enhanced Shock during this period.

Keep in mind that there are trace amounts of remaining water left in the plumbing from factory testing. Your hot tub will probably also receive higher than normal usage during the first month of ownership. For those reasons, your FROG System will be working overtime to sanitize the water and maintain a chlorine residual during the first week or so.

LEARN MORE

  • Test and balance your spa water weekly using a FROG Test Strip.
  • Replace the SmartChlor Cartridge when empty, based on the FROG Test Strip showing a lighter color than the out indicator on the bottle.
  • Shock your water with Chlorinating Concentrate or Enhanced Shock once or twice per month, depending on usage.
  • Clean your filters every 30 days with SpaGuard Filter Cleaner – remove the filters, saturate surface with cleaner, allow to sit for 15-20 minutes, then hose the filters off with a high pressure hose or Water Wand. Ensure ALL soap is removed before placing the filters back to avoid foaming. *To avoid issues with foam, try to keep all detergents, lotions, oils, soaps, makeup, perfume, and hair products out of the water!
  • Drain, clean, and refill your spa water every 4 months, following the start-up instructions. Over time, the total dissolved solids build up and saturate the water, preventing proper sanitation and balancing. A new FROG @ease Floating System Start-Up Kit will contain the Cartridges, Test Strips, and Jump Start that you need. It’s important to discard the used Mineral Cartridge after 4 months, whether you replace it or not. After this time period, it loses its efficacy and will cause cloudy water.
  • Check your water balance. If your pH or Total Alkalinity is off, SmartChlor will not be as effective.
  • Check to see if your FROG @ease SmartChlor Cartridge is empty.
  • Increase the dial setting if needed. If the FROG @ease SmartChlor Cartridge is not empty, try turning up the dial one setting.
  • Make sure your minerals have not been used for more than 4 months. When you hear minerals left inside, it is because one of the minerals does not completely dissolve – SmartChlor will only be effective when used with active FROG minerals.

Over-chlorination is virtually impossible with the FROG @ease System due to the self-regulating process that converts the Chlorine Reserve to Free Chlorine automatically when needed.

When testing SmartChlor with a standard test strip, you will see the Total Chlorine is higher than the Free Chlorine, which is perfectly OK. The Total Chlorine is the SmartChlor reserve that is inactive; when the hot tub needs more Free Chlorine to kill bacteria, it pulls from the Reserve. That’s why we recommend using the FROG @ease Test Strips – a 4-month supply comes with every FROG @ease Sanitizing System.

The @ease System combines the proven FROG mineral formula for killing bacteria with SmartChlor Technology that maintains a consistently low chlorine level for weeks.

Unlike normal chlorine that is used up when you enter the spa, SmartChlor continues to maintain the same level, which is up to 75% less than hot tubs using DiChlor (standard hot tub chlorine). That’s why it’s called self-regulating – it goes to work when the hot tub needs sanitizing so there are no frustrating yo-yo levels. This time-released method is also why less shock is needed to maintain the hot tub.

This technology is so unique it has its own testing method that’s easier than standard test strips.

In 2 seconds, you can know precisely whether your pH, Total Alkalinity, and Calcium Hardness are balanced, plus whether or not the SmartChlor Cartridge needs replacing. Simply dip the FROG @ease Test Strip into the water, remove with the pads facing up, and shake once to remove the water on the FROG Test Strips. Then hold it up next to the color chart on the back of the bottle to compare colors.

If the SmartChlor color on the strip is darker than the bottle label, the water is fine. If it’s lighter, then simply replace the SmartChlor Cartridge!

This technology is so unique it has its own testing method that’s easier than standard test strips.

Why can’t I use another test strip? The FROG @ease SmartChlor Cartridge forms a reserve that will be inaccurately measured as total chlorine on other test strips. Unlike conventional chlorine, the SmartChlor reserve readily shifts to free chlorine as needed, maintaining spa health with a low level of chlorine.

A new standard for keeping your hot tub water crystal clear – continuously.

So no touching chemicals, no bad smells, no faded swim suits.

SmartChlor Cartridges maintain a SmartChlor reserve in the water based on the output level you set, automatically delivering more free chlorine as needed and maintaining a consistent 0.5-1.0 ppm free chlorine level at all times. In other words, no frustrating yo-yo chlorine levels!

What size hot tub will FROG @ease work in?

Hot tubs 150 to 600 gallons are perfect for FROG @ease.

How does FROG @ease compare to bromine floaters or using chlorine?

With standard chemicals, you experience peaks and valleys in your sanitizing routine. When you add chemicals, the level spikes, and when you use the hot tub, the level drops. This yo-yo method goes away with FROG @ease because it maintains the same level of sanitizing all the time. Plus, it’s conveniently tucked away with easy access whenever you need to change a cartridge.

How can it work so well with 75% less chlorine?

SmartChlor is not a typical chlorine. It will consistently maintain a 0.5 to 1.0 ppm free chlorine level. This wouldn’t be enough on its own, but with FROG minerals, it’s a perfect combination that kills bacteria 2 ways so you have a cleaner, clearer hot tub that’s wonderfully soft and odor free!

How long do the Mineral and SmartChlor cartridges last?

The mineral cartridge lasts four months (or change whenever you drain and refill your hot tub). The SmartChlor Cartridge lasts 3-4 weeks depending on the size of your spa and how often it is used.

Is a FROG @ease System expensive?

SmartChlor is slightly more expensive than dichlor but less than some other systems. Consumers who have tried it tell us it’s SO worth the money, because it makes owning a hot tub extremely easy with far less monitoring and shocking. Plus with up to 75% less chlorine, your suits won’t fade and your hot tub itself has less wear and tear.

Can I remove FROG @ease from the spa while I’m relaxing in the water?

Yes. Simply set it on a surface that is not susceptible to bleaching and remember to replace it when you exit the hot tub.

Contact Us
Get in touch with our team of home and backyard leisure specialists today.
everything billiards and spas in NC Logo

Winston Salem

6000 Meadowbrook Mall Ct
Suite 7A Clemmons, NC

Coming Soon!

Charlotte

1820 Westinghouse Blvd
Unit G Charlotte, NC

Coming Soon!

Copyright ©2021 Everything Billiards & Spas. All rights reserved. Made with by IMP Digital - powered by Kinsta
Shopping cart

Sign in

No account yet?